21-02-2011, 12:06 PM
can you please help me with project- dc motor control using four quadrant chopper. I am a final year b.tech electrical student
|
dc motor control using four quadrant chopper
|
can you please help me with project- dc motor control using four quadrant chopper. I am a final year b.tech electrical student
01-03-2012, 01:08 PM
hi
please go through the below thread for more details on 'Speed Control of D.C shunt motor using four Quadrant Chopper'
http://studentbank.in/report-four-quadra...?pid=29049
please go through the below thread for more details on 'Speed Control of D.C shunt motor using four Quadrant Chopper'
http://studentbank.in/report-four-quadra...?pid=29049
12-06-2012, 01:23 PM
DC MOTOR CONTROL USING CHOPPER
DC MOTOR CONTROL.pdf (Size: 1.37 MB / Downloads: 2)
ABSTRACT
The speed of separately excited DC motor can be controlled from below and up to rated speed using chopper as a converter. The chopper firing circuit receives signal from controller and then chopper gives variable voltage to the armature of the motor for achieving desired speed. There are two control loops, one for controlling current and another for speed. The controller used is Proportional-Integral type which removes the delay and provides fast control. Modeling of separately excited DC motor is done.
INTRODUCTION
Development of high performance motor drives are very essential for industrial applications. A high performance motor drive system must have good dynamic speed command tracking and load regulating response. DC motors provide excellent control of speed for acceleration and deceleration. The power supply of a DC motor connects directly to the field of the motor which allows for precise voltage control, and is necessary for speed and torque control applications.
DC CHOPPER
A chopper is a static power electronic device that converts fixed dc input voltage to a variable dc output voltage. A Chopper may be considered as dc equivalent of an ac transformer since they behave in an identical manner. As chopper involves one stage conversion, these are more efficient [2]. Choppers are now being used all over the world for rapid transit systems. These are also used in trolley cars, marine hoist, forklift trucks and mine haulers. The future electric automobiles are likely to use choppers for their speed control and braking. Chopper systems offer smooth control, high efficiency, faster response and regeneration facility [2].
PRINCIPLE OF CHOPPER OPERATION
A chopper is a high speed “on" or “off” semiconductor switch. It connects source to load and load and disconnect the load from source at a fast speed. In this manner, a chopped load voltage as shown in Fig. is obtained from a constant dc supply of magnitude Vs. For the sake of highlighting the principle of chopper operation, the circuitry used for controlling the on, off periods is not shown. During the period Ton, chopper is on and load voltage is equal to source voltage Vs. During the period Toff, chopper is off, load voltage is zero. In this manner, a chopped dc voltage is produced at the load terminals [2].
CURRENT- LIMIT CONTROL [2]
In this control strategy, the on and off of chopper circuit is decided by the previous set value of load current. The two set values are maximum load current and minimum load current. When the load current reaches the upper limit, chopper is switched off. When the load current falls below lower limit, the chopper is switched on. Switching frequency of chopper can be controlled by setting maximum and minimum level of current.
DC MOTOR CONTROL.pdf (Size: 1.37 MB / Downloads: 2)
ABSTRACT
The speed of separately excited DC motor can be controlled from below and up to rated speed using chopper as a converter. The chopper firing circuit receives signal from controller and then chopper gives variable voltage to the armature of the motor for achieving desired speed. There are two control loops, one for controlling current and another for speed. The controller used is Proportional-Integral type which removes the delay and provides fast control. Modeling of separately excited DC motor is done.
INTRODUCTION
Development of high performance motor drives are very essential for industrial applications. A high performance motor drive system must have good dynamic speed command tracking and load regulating response. DC motors provide excellent control of speed for acceleration and deceleration. The power supply of a DC motor connects directly to the field of the motor which allows for precise voltage control, and is necessary for speed and torque control applications.
DC CHOPPER
A chopper is a static power electronic device that converts fixed dc input voltage to a variable dc output voltage. A Chopper may be considered as dc equivalent of an ac transformer since they behave in an identical manner. As chopper involves one stage conversion, these are more efficient [2]. Choppers are now being used all over the world for rapid transit systems. These are also used in trolley cars, marine hoist, forklift trucks and mine haulers. The future electric automobiles are likely to use choppers for their speed control and braking. Chopper systems offer smooth control, high efficiency, faster response and regeneration facility [2].
PRINCIPLE OF CHOPPER OPERATION
A chopper is a high speed “on" or “off” semiconductor switch. It connects source to load and load and disconnect the load from source at a fast speed. In this manner, a chopped load voltage as shown in Fig. is obtained from a constant dc supply of magnitude Vs. For the sake of highlighting the principle of chopper operation, the circuitry used for controlling the on, off periods is not shown. During the period Ton, chopper is on and load voltage is equal to source voltage Vs. During the period Toff, chopper is off, load voltage is zero. In this manner, a chopped dc voltage is produced at the load terminals [2].
CURRENT- LIMIT CONTROL [2]
In this control strategy, the on and off of chopper circuit is decided by the previous set value of load current. The two set values are maximum load current and minimum load current. When the load current reaches the upper limit, chopper is switched off. When the load current falls below lower limit, the chopper is switched on. Switching frequency of chopper can be controlled by setting maximum and minimum level of current.
|
« Next Oldest | Next Newest »
|
