dark detector pdf
#1

I want to how dark detector prepared by one transistor,2 resistors, LDR, LED, BATTERY will work.I want to know how it works.
Reply
#2

Darkness detector is simply a LDR (Light Dependent Resistor) interfaced square wave generator. In this project the square wave generator is developed as a 555 Timer IC based ASTABLE MULTIVIBRATOR. Before going any further we must get the basic details on the LDR. The figure below shows an image of various types of LDR.
Various types of LDR
What is LDR?

LDRs are made from semiconductor materials to enable them to have their light sensitive properties. There are many types but one material is popular and it is cadmium sulphide (CdS). These LDRs or PHOTO REISTORS works on the principle of “Photo Conductivity”. Now what this principle says is , whenever light falls on the surface of the LDR (in this case) the conductance of the element increases or in other words the resistance of the LDR falls when the light falls on the surface of the LDR. This property of the decrease in resistance for the LDR is achieved because it is a property of semiconductor material used on the surface.
Here in this dark detector circuit, LDR is configured with 555 ASTABLE in such a way that 555 ASTABLE generates square wave when the light intensity goes below a certain level.

Circuit Components

+5 to +10 supply voltage
555 IC
100KΩ resistor
22KΩ resistor
10KΩ resistor
1MΩ pot or variable resistor
104(100nF) capacitor
2N3906 transistor
LDR(any size)
Speaker (25Ω,0.5WATT) or any other speaker.

Circuit Diagram

Dark Detector Circuit Diagram
Above figure shows the circuit diagram of dark detector alarm. After some observation the circuit should seem very similar to the ASTABLE MULTIVIBRATOR, that is because the circuit is a ASTABLE MULTIVIBRATOR with only one modification. This modification is done at RESET pin (PIN4). In a normal ASTABLE vibrator this pin is connected to +5V, but since in this case we are supposed to generate pulse on the condition of absence of light it is not connected directly to +5v. The resistor network provided at the RESET pin provides a virtual ground so to keep resetting the IC and so the square wave output is stopped in the presence of light.
The transistor here drives the speaker because the speaker driven by IC is not a good idea. The speaker here can be replaced with LEDs to create an output response of lighting. So once the LEDs are placed and the darkness falls we will have an emergency backup light.
The transistor here need not be a PNP compulsory but one can replace it with a NPN and the pin connections should be connected accordingly.

Working

Before going to explanation, the circuit should be assumed ON and is not buzzing in the presence of light. This condition of non-buzzing in the presence of light can be achieved by adjusting the 1MΩ trim pot. Now in the circuit one can observe a voltage divider with 1M, 100K on one side and LDR on the other, the reset pin is connected in the middle. The trimmer pot is said to be adjusted because to create enough resistance on the top branch of voltage divider to drop almost all the potential (+5v) in the top branch itself. This leaves a virtual ground at the middle of divider (reset pin). Since the RESET pin of 555 is a LOW LEVEL triggered, the timer IC will be reset mode continuously and so there will be no square wave output as it should be. From this we can conclude that in the presence of light the 555 IC will be in complete reset and provides no output.
Now when the darkness falls on the LDR, the resistance of the LDR increases drastically as explained in introduction, this increase of resistance in the second branch (one with LDR) of voltage divider will be enough to change the ratio of voltage sharing between the two branches of voltage divider section. Once this happen, the potential at the junction of voltage divider circuit rises from 0V to 2V (approximately). And similarly the voltage at the RESET pin rises. This rise of voltage will be enough to lift the 555IC from reset mode. Once this reset mode is lifted, the timer generates square wave output. So it is concluded that once the darkness falls on the LDR the square wave output is generated by the timer.
The square wave generated by the timer is fed to the PNP transistor to drive the speaker. So the speaker outputs sound in response to the square wave.

Common Errors

Even after adjusting the trim pot the buzzing do not stop.
The LDR might have enough resistance to put a potential at the reset pin. Put another 100KΩ resistor in series with 1MΩ pot.
Check if the RESET pin (PIN4) is accidentally connected to +5V rail in any way.
There is no buzzing even in the dark.
LDR might not be developing enough potential at the reset pin. Put a pot in series with LDR and adjust it to get buzzing.
Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Popular Searches: ppt by dark ness detector circuit, the darkness, pdf report of dark detector ckt, darkness, cd4069 astable, ppt for dark detector project, dark detector using ic555 pdf,

[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  life cycle of dark fantasy biscuit 0 541 14-07-2018, 06:13 PM
Last Post: Guest
  project on fake indian curruncy detector 0 620 10-07-2018, 09:07 PM
Last Post: Guest
  vegakit 557 metal detector working 1 488 03-02-2018, 11:04 AM
Last Post: dhanabhagya
  download pdf of transducer multiple choice questions answer in pdf 1 838 27-01-2018, 01:23 PM
Last Post: dhanabhagya
  literature review underground cable fault detector 1 480 16-12-2017, 09:45 AM
Last Post: jaseela123d
  metal detector vk 557 not working 2 820 20-11-2017, 03:45 PM
Last Post: Guest
  metal detector vk 557 mini project circuit diagram working 2 667 20-11-2017, 03:44 PM
Last Post: Guest
  metal detector vk 557 mini project circuit diagram working 2 1,378 20-11-2017, 12:11 PM
Last Post: Guest
  pdf full project report on electronic letter box pdf 2 978 14-11-2017, 04:11 PM
Last Post: jaseela123d
  pdf full project report on electronic letter box pdf 1 948 14-11-2017, 04:10 PM
Last Post: jaseela123d

Forum Jump: