Automatic Phase Selector (APS)
#1

Abstract:
Auto Phase Selector (APS) system is used to ensure continuous supply to load in case mains supply is not healthy. This unit is very useful at the sites at which mains supply is irregular. It may be sometimes very high or sometimes very low voltage. The frequent failures/fluctuations of power affects life of power plant and battery. The objective of the APS is to ensure that there is continued commercial power supplied to the site at all times so as to ensure that the Base Transceiver Station (BTS) runs on commercial power until all available phases are either out of electrical tolerance or completely off. This is a micro controller based unit and is used with three phase electrical supply. Whenever the supply of one or two phases of a three phase electrical line goes off, the APS system automatically distributes the electrical supply from the active phase to the failed phases. This ensures continuous power supply through all the three phases even if one phase is active.
Reply
#2
Sir. I will be glad to have a detail information on this project. Thanks for your good works.
Reply
#3
I'm working on my final year project and i need info on automatic phase selector; actually between three phases. How can i get info on a past similar work that has been done before now?
Thanks
Reply
#4
Hi, Danno4krist
To do the switching need to use SSR's, Solid State Relays, they can react in one half of a cycle. However being jumping from phase to phase have some phase overlap issues that would require a added half cycle delay between shut off one phase to the connection of another phase. Plus switching phases on the go will cause some possible spiking issues due to the AC current cycles jumping ahead or back 120 degrees time wise.

However to get a reasonable voltage reading off each phase it would still take a few cycles for the system to accurately detect a low voltage condition and make the needed choice of which phase line is the best next alternative.

might be to use back to back SCR's as the switching elements, with phase and voltage detection to decide on the switching action.
As one phase goes low, turn that phase off and turn the other phase on. If done right this might work if the lines dont go down too often in a day.
It would surely be a good idea to test this in a simulator first however to make sure the switching matrix method works ok. There will most likely have to be phase detection to get the switching action correct.
For the switching, perhaps a micro controller or PROM and associated comparators to make the decisions.

If the switching SCR's dont work because of too much phase overlap, have to use an alternate means such as a transistor with bridge rectifier. I think you would have to analyze the effect of switching one phase to the other first anyway though, the effect on the load. The load may have to take a brief interruption in power. If that's not a problem, SCR's would work ok.
Reply
#5
hiiiiiiifffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff
Reply
#6
can u post the abstract for the automatic phase selector
Reply
#7

to get information about the topic "Automatic Phase Selector " full report ppt AND related topic refer the page link bellow

http://studentbank.in/report-automatic-p...e=threaded

http://studentbank.in/report-automatic-p...e=threaded
Reply
#8
From tneb , how they do active phase selector from 3¢ supply to 1¢ load
Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Popular Searches: aps dpp, pdf for automatic phase sequence selector system, 3phase automatic phase selector literature review, literature review for automatic phase selector, aps companyormer fault problem ppt, show the circult diagram for automatic phase selector, automatic phase selector aps,

[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  AUTOMATIC STREET LIGHT CONTROL WITH SENSOR TECHNOLOGY seminar class 2 11,352 22-05-2017, 11:07 AM
Last Post: yasminoth93
  AUTOMATIC BUS STATION ANNOUNCEMENT SYSTEM full report project report tiger 4 10,508 13-08-2016, 11:16 AM
Last Post: jaseela123d
  Color Iris Recognition Using Quaternion Phase Correlation matlab project project topics 3 3,372 02-07-2016, 09:38 AM
Last Post: visalakshik
  HIGHWAY SPEED SENSING AND AUTOMATIC BREAKING SYSTEM smart paper boy 7 13,346 16-03-2016, 03:02 PM
Last Post: dhanabhagya
  AUTOMATIC STREET LIGHT CONTROL-EMBEDDED BASED PROJECT project topics 18 29,462 11-02-2016, 02:03 PM
Last Post: seminar report asees
  Wireless based Automatic dam water level control shutter open /closed with emergency smart paper boy 4 11,054 11-09-2015, 02:00 PM
Last Post: seminar report asees
  MICROCONTROLLER BASED AUTOMATIC RAILWAY GATE CONTROL full report project topics 49 57,562 10-09-2015, 03:18 PM
Last Post: seminar report asees
  AUTOMATIC WATER LEVEL MONITORING SYSTEM computer science crazy 3 4,799 23-10-2014, 11:47 PM
Last Post: jaseela123d
  Automatic Sun Tracking System (ASTS) electronics seminars 9 11,953 21-07-2014, 09:18 PM
Last Post: seminar report asees
  Automatic Room light Controller with Visitor Counter project topics 26 17,330 12-03-2014, 07:22 PM
Last Post: computer topic

Forum Jump: