anti lock braking system full report


Anti-Lock Braking Systems (ABS) are designed to maintain driver control and stability of the car during emergency braking. Locked wheels will slow a car down but will not provide steering ability. ABS allows maximum braking to be applied while retaining the ability to 'steer out of trouble'
The theory behind anti-lock brakes is simple. A skidding wheel (where the tire contact patch is sliding relative to the road) has less traction than a non-skidding wheel. By keeping the wheels from skidding while you slow down, anti-lock brakes benefit you in two ways: You'll stop faster, and you'll be able to steer while you stop.
An ABS system monitors four wheel speed sensors to evaluate wheel slippage. Slip can be determined by calculating the ratio of wheel speed to vehicle speed, which is continuously calculated from the four individual wheel speeds. During a braking event, the function of the control system is to maintain maximum possible wheel grip on the road - without the wheel locking - by adjusting the hydraulic fluid pressure to each brake by way of electronically controlled solenoid valves.

Car manufacturers world wide are vying with each other to invent more reliable gadgets there by coming closer to the dream of the ËœAdvanced safety vehicleâ„¢ or ËœUltimate safety vehicleâ„¢, on which research and development has been going on for the past several year. Most of the newer vehicle models offer ABS as either standard or optional equipment .Wheel lockup during braking causes skidding which in turn cause a loss of traction and vehicle control. This reduces the steering ability to change direction. So the car slides out of control. But the road wheel that is still rotating can be steered. That is what ABS is all about. With such a system, the driver can brake hard, take the evasive action and still be in control of the vehicle in any road condition at any speed and under any load. ABS does not reduce stopping distance, but compensates the changing traction or tyre loading by preventing wheel lockup.
During panic braking when the wheels are about to lockup, sensors sense that the wheel has just begun turning slower than others on the vehicle. So they momentarily reduce braking force on the affected wheel. This prevents sliding of the wheels on the pavement. When the wheel resumes rolling, full braking force is again applied. ABS repeats the process until there is no longer any need for modulated braking. ABS acts faster than any driver could, pumping the brakes several times per second. Depending on the type of system, ABS adjusts the braking force at each wheel or set of wheels, whereas a driverâ„¢s foot on the brake pedal operates all the brakes at once in normal braking.
The theory behind anti-lock brakes is simple. A skidding wheel (where the tire contact patch is sliding relative to the road) has less traction than a non-skidding wheel. If the vehicle have been stuck on ice and if the wheels are spinning then the vehicle have no traction. This is because the contact patch is sliding relative to the ice. By keeping the wheels from skidding while you slow down, anti-lock brakes benefit you in two ways: You'll stop faster, and you'll be able to steer while you stop. Good drivers have always pumped the brake pedal during panic stops to avoid wheel lock up and the loss of steering control. ABS simply gets the pumping job done much faster and in much precise manner than the fastest human foot.
A simple braking system consists of a master cylinder, and four wheel cylinders. Every wheel cylinder contains two pistons which move out words when the hydraulic fluid flows from the master cylinder to the wheel cylinders through the suitable pipes or lines.

Springs are used to hold the brake shoes on all four wheels. When the brake pedal is pressed the piston in the master cylinder forces the liquid out of the cylinder. This liquid presses the two pistons in the wheel cylinders outwards. These two pistons push the brake shoes out words. The brake shoes in turn press against the brake drums; this stops the brake drum which will be rotating.
When the brake pedal is released the master cylinder is pushed backwords.This is done by a spring fitted in the master cylinder. The springs of the brake shoe brings the shoes closer. The liquid in the wheel cylinder is pushed outwards through the pipes. It returns through the pipes to the master cylinder. This is how the hydraulic system of the four wheels operates
3.1 Master cylinder
It consists of a reservoir feedhole, bypass port, primarypiston, secondary piston .The liquid in the reservoir flows through bypass port to the master cylinder. When the pedal is pressed the primary piston moves to the left .when it crosses the bypass port the liquid is forced along the pipe lines to the wheel cylinders. When the pedal is released the primary piston is moved back wards .it is the spring, which pushes the piston back wards. At the same time a partial vacuum is developed in the space previously occupied by the spring.
The brakes of vehicle not equipped with ABS will almost immediately lock the wheels, when the driver suddenly applies the brake. In this case the vehicle slides rather than rolls to a stop. The skidding and lack of control was caused by the locking of wheels. The release and reapply of the brake pedal will avoid the locking of the wheels which in turn avoid the skidding. This is exactly what an antilock braking system does.
4.1 Pressure modulation
When the brake pedal is pumped or pulsed the pressure is quickly applied and released at the wheels. This is called pressure modulation. Pressure modulation works to prevent the wheel locking. ABS can modulate the pressure to the brake as often as 15 times per seconds. By modulating the pressure to the brakes the friction between the tires and the road is maintained and the vehicle is able to come to the controllable stop.
Steering is another important consideration. As long as a tire doesnâ„¢t slip it goes only in the direction in which it is turned. But once it is skid it has little or no directional stability.
The Maneuverability of the vehicle is reduced if the front wheels are locked and the stability of the vehicle is reduced if the rear wheels are locked.
ABS precisely controls the slip rate of the wheels to ensure maximum grip force from the tyre and it there by ensures maneuverability and stability of the vehicle. ABS control module calculates the slip rate of the wheels based on the vehicle speed and speed of the wheels, and then it controls the brake fluid pressure to attain the target slip rate.

During ABS operation, the target slip rate can be from 10 to 30%. 0% slip means the wheel is rolling freely, while 100 % means the wheel is fully locked. A slip rate of 25 % means the velocity of a wheel is 25 % less than that of a freely rolling wheel at the same vehicle speed.
Many different ABS are found on todayâ„¢s vehicles. These designs are varied by their basic layout, operation and components. The ABS components can be divided into two categories.
1. Hydraulic components
2. Electrical/electronic components
Besides these normal and conventional brake parts are part of the overall brake system.
5.1 Hydraulic components
¢ Accumulator
An accumulator is used to store hydraulic fluid to maintain high pressure in the brake system and provide the residual pressure for power assisted braking. Normally the accumulator is charged with nitrogen gas and is an integral part of the modulator unit.
¢ Antilock hydraulic control valve assembly
This assembly controls the release and application of the brake system pressure to the wheel brake assemblies. It may be of integral type and non integral type. In integral type the unit is combined with the power boost and master cylinder unit into one assembly. The non integral type is mounted externally from the master cylinder /power booster unit and is located between the master cylinder and wheel brake assembly. Both types generally contain solenoid valve that control the releasing, holding and applying of brake system pressure.
¢ Booster pump
The booster pump is an assembly of an electric motor and pump. The booster pump is used to provide pressurized hydraulic fluid ABS. The pumps motor is controlled by systems control unit.
¢ Booster/Master cylinder assembly
It is referred as the hydraulic unit, contains the valves and pistons needed to modulate hydraulic pressure in the wheel circuit during the ABS operations.
¢ Fluid accumulator
Different than a pressure accumulator, fluid accumulator temporarily store brake fluid, that is removed from the wheel brake unit during ABS cycle. This fluid is then used by pump to build pressure for the brake hydraulic system.
¢ Hydraulic control unit
This assembly contains solenoid valve, fluid accumulator, pump and electric motor. The unit may have one pump and one motor or it have one motor and two pumps.
¢ Main Valve
This is a two position valve and is also controlled by ABS control module and is open only in the ABS mode. When open pressurized brake fluid from the booster circuit is directed into the master circuit to prevent excessive pedal travel.
¢ Modulator unit
The modulator unit controls the flow of pressurized brake fluid to the individual wheel circuits. Normally the modulator is made up of solenoid that open and close valves, several valves that control flow of fluid to wheel brake units and electrical relays that activate or deactivate the solenoids through the commands of the control module. This unit may also be called the hydraulic actuator, hydraulic power unit or the electro hydraulic control valve.
¢ Solenoid valves
The solenoid valves are located in the modulator unit and are electrically operated by signals from the control module. The control module switches the solenoids on or off to increase, decrease, or maintain the hydraulic pressure to the individual wheel units.
¢ Wheel circuit valves
Two solenoid valves are used to control each circuit or channel. One controls the inlet valve of the circuit, the controls the outlet valve .the position is determined by the control module. Outlet valves are normally closed and inlet valves are normally open. Valves are activated when abs control module switches 12 volts to the circuit solenoids. During normal driving the circuits are not activated.
5.2 Electrical\ electronic components
¢ ABS control module
This small computer is normally mounted inside the trunk on the wheel housing, mounted to the master cylinder or is part of the hydraulic control unit. It monitors system operation and controls antilock function when needed. The module relies on input from the wheel speed sensors and feedback from the hydraulic unit to determine if the abs is operating correctly and to determine when the anti lock mode is required.
¢ Brake pedal sensor
The antilock brake pedal sensor switch is normally closed. When the brake pedal exceeds the antilock brake pedal sensor switch setting during an antilock stop, the antilock brake control module senses that the antilock brake pedal sensor switch is open and grounds the pump motor relay coil. This energizes the relay and turns the pump motor on. When the pump motor is running, the hydraulic reservoir is filled with high pressure brake fluid and the brake pedal will be pushed up until antilock brake pedal sensor switch closes. when the antilock brake pedal sensor switch closes , the pump motor is turned off and the brake pedal will drop some with each abs control cycle until the antilock brake pedal sensor switch opens and the pump motor is turned on again .this minimizes pedal feedback during abs cycling .
¢ Pressure differential switch
It is located in the modulator unit. This switch sends a signal to the control module whenever there is an undesirable difference in the hydraulic pressures with in the brake system.
¢ Relays
Relays are electromagnetic devices used to control a high current circuit with a low current switching circuit. In abs relays are used to switch motors and solenoids. A low current signal from the control module energizes the relays that complete the electrical circuit for the motor or solenoid.
¢ Toothed ring
It can be located on an axle shaft, differential gear or a wheels hub. This ring is used with conjunction with the wheel speed sensor. The ring has a number of teeth around its circumference. As the ring rotates and each tooth passes by the wheel speed sensor, an ac voltage signal is generated between the sensor and tooth.
¢ Wheel speed sensor
It is mounted near the different toothed ring. As the rings teeth rotate past the sensor an ac voltage is generated. as the teeth move away from the sensor, the signal is broken until the next tooth comes close to the sensor .the end result is a pulsing signal that is sent to the control module. The control module translates the signal in to wheel speed. The sensor is normally a small coil of wire with a permanent magnet in its center.
One of the classifications of abs is integral and non integral type.
Integral type they combine the master cylinder, hydraulic booster and abs hydraulic circuit in to single hydraulic assembly.
In non integral type they use a conventional vacuum-assist booster and master cylinder. In addition they can be classified according to the control they provide.
6.1. Four channel, four sensors ABS
This is the best scheme. There is speed sensor on all four wheels and a separate valve for all the four wheels. With this set up the controller monitors each wheel individually to make sure it is achieving maximum braking force.
6.2. Three channel, three sensor ABS

This scheme is commonly found on pick up trucks with four wheels ABS, has a speed sensor and a valve for each of the front wheels, with one valve and one sensor for both rear wheels. The speed sensor for the rear wheel is located in the rear axle.
This system provides individual control of the wheels, so they can both achieve maximum braking force. The rear wheels however are monitored together, they both have to start to lock up before the abs will activate on the rear. With this system, it is possible that one of the rear wheels will lock during a stop, reducing brake effectiveness.
6.3. One channel, one sensor abs
This scheme is commonly found on pick up trucks with rear wheel abs .it has one valve ,which controls both rear wheels , and one speed sensor, located in the rear axle . This system operates the same as the rear end of the rear channel system. The rear wheels are monitored together and both have to start to lock up before the abs kicks in. in this system is also possible that one of the rear wheels will lock reducing brake effectiveness.
The hydraulic circuit for this type of system is an independent four channel type. One for each wheel. The hydraulic control unit is a separate unit. Normal braking is accompanied by conventional vacuum power assist brake system.
The system prevents wheel lock up during an emergency stop by modulating brake pressure. It allows the driver to maintain steering control and stop the vehicle in the shortest possible distance under most conditions. During ABS operation the driver will sense a pulsation in the brake pedal and clicking sound.
7.1 Operation
The ABS control module calculates the slip rate of the wheels and control the brake fluid pressure to attain the target slip rate if the control module senses that the wheel is about to lock based on input sensor data, it pulses the normally open inlet solenoid valve closed for that circuit. This prevents any more fluid from entering that circuit. ABS control module then looks at the sensor signal from the effected wheel again. If that wheel is still decelerating faster than other three wheels it opens the normally closed out let solenoid valve for that circuit. This dumps any pressure that is trapped between the closed inlet valve and the brake back to the master cylinder reservoir. Once the effected wheel returns to the same speed as the other wheel, the control module returns the valve to the normal condition allowing fluid flow to the effected brake.
Based on the input from vehicle speed and the wheel speed sensor, the control module calculates the slip rate of each wheel, and transmits a control signal to the modulator unit solenoid valve when the slip rate is high.
Wheel speed at each wheel is measured by variable reluctance sensors and sensor indicators. The sensors operate on magnetic induction principles.

As the teeth on brake sensor indicators rotate past the sensors, ac current is generated. The ac frequency changes in accordance with the wheel speed. The ABS control unit detects the wheel sensor signal frequency and there by detects wheel speed.
Some systems, which work with the ABS, are Automatic traction control and Automatic stability control, which are discussed below.
Automatic traction control systems apply the brakes when a drive wheel attempts to spin and lose traction. The system works best when one drive wheel is working on a good traction surface and the other is not. The system also works well when the vehicle is accelerating on slippery road surfaces, especially when climbing hills. ATC is most helpful on four wheel or all wheel drive vehicles in which loss of traction at one wheel could hamper driver control.
During road operation the ATC system uses an electronic control module to monitor the wheel speed sensors. If a wheel enters a loss of traction situation, the module applies braking force to the wheel in trouble. Loss of traction is identified by comparing the vehicle speed to the speed of the wheel. If there is a loss of traction the speed of the wheel will be greater than expected for the particular vehicle speed. ABS and ATC systems can be integral and uses the common valves.
These systems are designed to reduce wheel slip and maintain traction at the drive wheels when the road is wet or snow covered. The control module monitors wheel speed. If during acceleration the module detects drive wheel slip and if brakes are not applied, the control module enters into the traction control mode. The inlet and outlet solenoid valves are pulsed and allow the brake to be quickly applied and released.
In some systems when a loss of traction is sensed, it not only cycles the brakes but signals the engine control module to retard ignition timing and partially close the throttle as well, which in turn reduces engine output.
Many systems are equipped with a dash mounted warning light to alert the driver that the system is operating. There will also be a manual cut off switch so that the driver can turn off ATC operation.

Like ATC, the stability control systems are linked with the ABS. it can also be called Electronic Stability Programme (ESP). Stability control systems momentarily apply the brakes at any one wheel to correct over steer or under steer. The control unit receives signals from the typical sensors plus a yaw, lateral acceleration (G-force) and a steering angle sensor.
The system uses the angle of the steering wheel and the speed of the four wheels to calculate the path chosen by the driver. It then looks at lateral G-forces and vehicle yaw to measure where the vehicle is going. (Yaw is defined as the natural tendency for a vehicle to rotate on its vertical center axis). So it is also called Yaw control.

Under steer is the condition in which the vehicle is slow to respond to steering changes. Over steer occurs when the rear wheels try to swing around causing the car to spin. When the system senses under steer in a turn the brake at the inside rear wheel is applied. During over steer the outside front brake is applied. Relaying on the input from the sensors and computer programming the system calculates if the vehicle is going exactly in the same direction in which it is being steered. In case of any difference between what the driver is asking and what the vehicle is doing, the system corrects the situation by applying one of the right or left brakes.
It allows the driver to maintain directional stability and control over steering during braking
Safe and effective
Automatically changes the brake fluid pressure at each wheel to maintain optimum brake performance.
ABS absorbs the unwanted turbulence shock waves and modulates the pulses thus permitting the wheel to continue turning under maximum braking pressure.
It is very costly
Maintenance cost of a car equipped with ABS is more.

ABS has been so far developed to a system, which provides rapid, automatic braking in response to signs of incipient wheel locking by alternatively increasing and decreasing hydraulic pressure in the brake line
Statistics show that approximately 40 % of automobile accidents are due to skidding. These problems commonly occur on vehicle with conventional brake system which can be avoided by adding devices called ABS
If there is an ABS failure, the system will revert to normal brake operation. Normally the ABS warning light will turn on and let the driver know there is a fault
Automotive technology “Jack erjavec
Automobile engineering “ kirpal Singh
howstuffworks .com
4.1 Pressure modulation
5.1 Hydraulic components
5.2 Electrical\ electronic components
6.1. Four channel, four sensors ABS
6.2. Three channel, three sensor ABS
6.3. One channel, one sensor abs
8.1 automatic traction control
8.2 automatic stability control
thanks yar .
but if i get more info. like dia. then it will be more helpful
if u hav ppt or any other info. then send me
ppt of this topic is available in this thread:
Anti-Lock Braking Systems

.ppt   Anti-Lock Braking Systems.ppt (Size: 603 KB / Downloads: 14)

Mini Train-the-Trainer

Basic Functions of ABS Systems
Driver Instructions for Cars and Light Trucks
Driver Instructions for Heavy Trucks
Resources for Defensive Driving Program Integration.

Basic Functions of ABS

Physics 101: Static Friction is Greater than Moving Friction
ABS IS Computer Controlled Brake Pedal “Pumping”
ABS Allows the Driver To Maintain Control During Hard Braking

Vehicle ABS System

Speed Sensors on Wheels are Monitored by On Board Computer
Radical Speed Differences Trigger ABS Action
ABS “Pumps” the Brakes 18 Times per Second
ABS Systems “Counter-Intuitive” Operations
Grinding Sounds from All Wheels
Pulsating or Soft Brake Pedal
Driver Can Still Steer (with Reduced Effect)

Driver Training Integration

ABS Systems Differ from Traditional Braking Training
Items to Incorporate
Basic Function of ABS Systems
How to Drive and Brake with ABS
What Happens when ABS Engages
Emphasize Steering!

to get information about the topic "anti lock braking system ppt " full report ppt and related topic refer the page link bellow

i want assembly language code for this "Anti-lock braking system" so please mail me urgently my mail id :raghurambodapati007[at];raghurambodapati[at]

To get full information or details of anti lock braking system please have a look on the pages

if you again feel trouble on anti lock braking system please reply in that page and ask specific fields in anti lock braking system

Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Popular Searches: anti lock braking system pdf, anti lock brake system report pdf, anti lock braking report full for seminar, report on hydraulic braking system, aircraft anti skid braking system, integral, methodolgy of anti lock braking system,

Quick Reply
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  NanoTechnology (Download Full Seminar Report) Computer Science Clay 39 51,367 16-08-2018, 01:41 PM
Last Post: pradeepkumar.M
  magnetic refrigeration full report project report tiger 46 43,790 20-06-2018, 11:43 PM
Last Post: Guest
  TQM Total quality management full report project report tiger 5 13,317 18-09-2016, 08:41 PM
Last Post: velraj
  pneumatic operated emergency braking system karthik hr 3 2,646 01-09-2015, 07:08 PM
Last Post: Guest
  thermoacoustic refrigeration full report project report tiger 12 19,183 06-03-2015, 06:28 PM
Last Post: Guest
  the gurney flap full report project report tiger 1 3,153 04-12-2014, 02:02 PM
Last Post: pricemuzDet
  exhaust gas recirculation full report project report tiger 8 10,341 05-11-2014, 09:06 PM
Last Post: jaseela123d
  IMPROVEMENT OF THERMAL EFFICIENCY BY RECOVERY OF HEAT FROM IC ENGINE EXHAUST full rep project report tiger 7 8,053 18-10-2014, 10:35 PM
Last Post: jaseela123d
  reverse engineering full report project report tiger 3 6,104 11-10-2014, 10:49 PM
Last Post: Guest
  sensotronic brake control full report computer science technology 13 23,207 07-10-2014, 10:01 PM
Last Post: seminar report asees

Forum Jump: