Abstract :
For the past ten years, organic materials have been extensively investigated as an electronic material for thin film transistor (TFT) devices. Organic materials offer strong promise in terms of properties, processing and cost effectiveness and they can be used in flat panel displays, imagers, smart cards, inventory tags and large area electronic applications. In this review, There is a particular need to develop air-stable n-channel (electron-conducting) organic semiconductors with performance comparable to that of p-channel (hole- ....etc

[:=Read Full Message Here=:]

use of voice morphing in film industry,use of voice morphing in forensic voice identification ....etc

[:=Read Full Message Here=:]

laser film is transmissive laser based play back medium. Working on the topology that laser has to shine through one side of the disc to a receiving sensor on the other side, where the beam of the laser would be interrupted by a spiral of small dots on the disc,which can then modulate the laser beam to represent the video and audio information, which was then interpreted by the receiving sensor receiving the beam on the other side Made of the ordinary photographic film, similar to the Select avision CED videodisc system, this wasnâ„¢t succe ....etc

[:=Read Full Message Here=:]

ABSTRACT
Geneva drive or Maltese cross is a indexing mechanism that converts the continuous motion into intermittent motion. By means of this mechanism the rotary motion of the driver wheel is converting into intermittent rotary motion of sprocket. The film passed over the sprocket. Due to the intermittent motion, the film advanced frame by frame in front of lens for 1/24th second in frequency of 48 Hz.
CHAPTER 1
INTRODUCTION
Geneva mechanism is commonly used indexing mechanis ....etc

[:=Read Full Message Here=:]

Lin Xiao,§
Zhuo Chen,§
Chen Feng
Liang Liu
Zai-Qiao Bai
Yang Wang
Li Qian
Yuying Zhang
Qunqing Li
Kaili Jiang
Shoushan Fan


Abstract

We found that very thin carbon nanotube films, once fed by sound frequency electric currents, could emit loud sounds. This phenomenon
could be attributed to a thermoacoustic effect. The ultra small heat capacity per unit area of carbon nanotube thin films leads to a wide
frequency response range and a high sound pressure level. On the basis of this finding, we made practical ....etc

[:=Read Full Message Here=:]

im sravani.laser film technical seminar paper presentation..im studying btech final year..i have to give seminar in my college about laser film
send laser film paper presentation to my mail id..i need it today..i have to ive seminar on this topic ....etc

[:=Read Full Message Here=:]

Abstract
Organic thin-film transistors OTFTs have received considerable attention recently because they can be fabricated at reduced temperature and potentially reduced cost compared to hydrogenated amorphous silicon thin-film transistors. Low fabrication temperature allows a wide range of substrate possibilities and makes OTFTs an attractive technology for many low-cost electronics applications, particularly those that require or may benefit from flexible polymeric substrates such as rf identification tags, smart cards ....etc

[:=Read Full Message Here=:]

Introduction

Plastics today are larger serving as substitute material in the field of tooling and prototype parts but are being used as engineering materials in their own lights and in many applications, they are doing better job then any other material could do, some authorities claim that the rapid advancement of plastic tooling would have been impossible without the versatility of the epoxyresin.
Plastic tooling offers several advantages over conventional metal tooling. These includes:


1. Lowest cost
2. Less time.
3. Light weig ....etc

[:=Read Full Message Here=:]

Plastics today are larger serving as substitute material in the field of tooling and prototype parts but are being used as engineering materials in their own lights and in many applications, they are doing better job then any other material could do, some authorities claim that the rapid advancement of plastic tooling would have been impossible without the versatility of the epoxyresin. Plastic tooling offers several advantages over conventional metal tooling. These includes:

1. Lowest cost

2. Less time.

3. Light weight, easily handled ....etc

[:=Read Full Message Here=:]

Moulds in Casting of Plastics and Thermoforming


Plastics today are larger serving as substitute material in the field of tooling and prototype parts but are being used as engineering materials in their own lights and in many applications, they are doing better job then any other material could do, some authorities claim that the rapid advancement of plastic tooling would have been impossible without the versatility of the epoxyresin.
Plastic tooling offers several advantages over conventional metal tooling. These includes:


1. Lowest ....etc

[:=Read Full Message Here=:]