Integrating the cell
Integrating the cell into a larger manufacturing system is basically a step up the system hierarchy of figure 3-5.Now the problems become ones concerning the cell as a whole (or, to use the earlier lexicon, a module). This purpose of this section is not to provide a detailed set of guidelines for the system design but to consider the most important features of the system and to discuss the relationship between the cells and the system.

5.1. System Definition

The system should be usable as a building block for a comp ....etc

[:=Read Full Message Here=:]

Materials

The majority of gears are composed of carbon and low-alloy steels, including carburised steels. Among the carburised steels used in gears are 1018, 1524, 4026, 4118, 4320, 4620, 4820, 8620 and 9310. The intended gear use will dictate the material used in its creation. For example gears to be used in food processing are made of stainless steels or nickel-base alloys because of their corrosion resistance.


Gear manufacturing processes

There are multiple ways in which gear blanks can be shaped through the cutting and fin ....etc

[:=Read Full Message Here=:]

Altezza camshafts reassembling and timing ....etc

[:=Read Full Message Here=:]

Abstract:
Mass customization manufacturing (MCM) has been gaining recognition as an industrial revolution in the 21st century. This paper presents innovative approaches in realizing and exercising MCM in theoretical and practical applications. Strategies of generalized production line platform and modularization are explored to support dynamic reconfigurations of MCM. NISTâ„¢s XML-based Shop Data information integration specification is utilized to derive a data driven reconfigurable MCM modeling methodology. A simulation model of a Boei ....etc

[:=Read Full Message Here=:]

Introduction

The wide deployment and applications of automatic sensing devices and computer systems have resulted in both temporally and spatially dense data-rich environments, which bring new challenges in quality engineering. Data fusion, through integration of engineering domain knowledge with data analysis techniques from advanced statistics, signal processing, decision making and control, represents one of the frontiers in quality improvement research for complex systems. In this presentation, an overview of ongoing research activiti ....etc

[:=Read Full Message Here=:]

Hello,

Presently I am using forging for manufacturing cam shaft.

The yield I am achieving 60%.To improve the yield to 75 % do you have any alternate process please provide.

Material : Low Carbon Steel.

Application : Used in Fuel Injection Pump operates at 1500 Rpm and Higher load. ....etc

[:=Read Full Message Here=:]

Camshaft


Double overhead cams control the opening and closing of the valves
The camshaft is used in IC Engines to operate poppet valves. It consists of a cylindrical rod running the length of the cylinder bank with a number of oblong lobes or cams protruding from it, one for each valve. The cams force the valves open by pressing on the valve, or on some intermediate mechanism, as they rotate.
The relationship between the rotation o ....etc

[:=Read Full Message Here=:]

OVERHEAD CAMSHAFT ENGINE
* INTRODUCTION :-
OHV means OverHead Valve –
An engine design where the camshaft is installed inside the engine block and valves are operated through lifters, pushrods and rocker arms (an OHV engine also known as Pushrod engine).
Although an OHV design is a bit outdated, it has been successfully used for decades. An OHV engine is very simple, has more compact size and proven to be durable.
* Classification :-
Single OverHead Cam
Double OverHead Cam
Pushrod Engines
* Single O ....etc

[:=Read Full Message Here=:]

Introduction

Due to innovations in sensor technology and rising complexity of manufacturing processes, increasingly more sensors are distributed throughout manufacturing and production systems to maintain the production performance, to ensure the life-cycle quality of products, and to improve the quality of management and service. This system-wide deployment of sensing devices is referred to as a distributed sensor system. Distributed sensor systems have resulted in a data-rich manufacturing environment and provide us unprecedented opport ....etc

[:=Read Full Message Here=:]

Submitted By
Shivek dhar


ABSTRACT
Gone through a rigorous four weeks training under the guidance of capable engineers and workers of bajaj motors limited, headed by the executive director of the company Mr. J.C Jha in the machining plant situated in Narsinghpur, Gurgaon, Haryana.
The training was specified under the CAMSHAFT department of the machining unit. Working under the cam machining department the basic grinding, scaling and machining was shown on heavy to medium duty lathes planted in the same ....etc

[:=Read Full Message Here=:]