hi boss
i wanted a report and ppt on abrasive jet machining
plz can u help me........ ....etc

[:=Read Full Message Here=:]

Water Jet cutting services make use of a super high pressure stream of water that carries an abrasive grit. This abrasive mixes with the water through a venturi effect in what is commonly called the ?focusing tube? just prior to cutting. This mixture of water and abrasive grit exit the focusing tube at speeds of approximately mach 2.5. Cutting pressures range between 45,000 to 60,000 psi for standard cutting models. For brittle, fragile, or delicate materials, piercing pressures range between 15,000 to 20,000 psi, and resume the higher cutting ....etc

[:=Read Full Message Here=:]

Camelina sativa is an oilseed crop and it might be used as fuel in aircrafts in the near future. A study conducted at Michigan Technological University claimed that Camelina has shown to be one of the more promising alternatives to petroleum jet fuel. They studied the whole process i.e. from planting to airplaneâ„¢s tailpipe. David Shonnard, Robbins Chair Professor of Chemical Engineering, studied the carbon dioxide emissions of jet fuel made from Camelina oil ....etc

[:=Read Full Message Here=:]

give me a report on this topic i want for my assignment please give me as early as possible ....etc

[:=Read Full Message Here=:]

Abrasive Jet Machining
abstract

Abrasive water jet machine tools are suddenly being a hit in the market since they are quick to program and could make money on short runs. They are quick to set up, and offer quick turn-around on the machine. They complement existing tools used for either primary or secondary operations and could make parts quickly out of virtually out of any material. One of the major advantage is that they donot heat the material. All sorts of intricate shapes are easy to make. They turns to be ....etc

[:=Read Full Message Here=:]

NO-MOVING-PART
HYBRID-SYNTHETIC JET ACTUATOR
Article Outline
1. Introduction
2. The actuator model
2.1. General
2.2. Amplifier
2.3. Feedback loop
3. Results
3.1. Oscillation frequency
3.2. Modified Strouhal number
3.3. Constant Strouhal number regime
3.4. Constant propagation velocity regime
4. Conclusions
Acknowledgements
References
1. Introduction

Actuators based on the synthetic jet idea are currently becoming of increasing importance for a number of applications, especially involving control of flo ....etc

[:=Read Full Message Here=:]

please send me the seminar on this topic i need it immediately ....etc

[:=Read Full Message Here=:]

Abresive Jet Machine



It is a newly developed technology used in industrial countries. This is adopted for machining operations.


Features

In this machine a high velocity of abrasive stream is used for machining. The abrasive particle have a vibration of about 50 hertz is mixed with high pressure gas or air in the mixing chamber. Then the stream is emerges through a small nozzle mounted on a fixture to the work piece.
Variable in abrasive jet machine
The variables that influence the rate of metal removal and accuracy of machining ....etc

[:=Read Full Message Here=:]

a high pressure water jet in rock cutting.


Presented by
Nandharaj .M
S8MB .102

Guided by
Dr santhoshkumar .N


Comparison of conventional and Abrasive water jet machining


Conventional machining

Contact mechanisms
Detonation of an explosive with in a confined space
damage is normally in the form of a narrow slot of varying depth



Abrasive water jet machining


non‐contact mechanisms
application of high Pressure water jets
--
Lower machine vibration
increased product size.
l ....etc

[:=Read Full Message Here=:]

when i was searching for my seminar topic i was attracted towards this site homepage and decided to make use of this site only.i want some help about above given topic.i will be highly obliged to u if u help me.please send me some matter about this topic and seminar report.please help me in making me this seminar an immpresive.. ....etc

[:=Read Full Message Here=:]