how to use the chart SELECTION OF MODULE & FACE WIDTH CHART OF SPUR GEAR
in gear design ....etc

[:=Read Full Message Here=:]

Integrating Structural Design and Formal Methods in RealTime System Design

Formal methods have been advocated as one of those techniques that can produce highquality software and hardware systems that has been demonstrated to come in ontime, within budget, and satisfy procurer requirements. They are, however, perceived to be difficult to use and unsuitable for presentation to nonspecialists. In addition, they have been criticized for paying too little attention to the system development process.
....etc

[:=Read Full Message Here=:]

Common Emitter BJT Amplifier Design Current Mirror Design


Some Random Observations
● Conditions for stabilized voltage source biasing
● Emitter resistance, RE, is needed.
● Base voltage source will have finite resistance, RB.
● needs to be much larger than RB.
● Small RB - relative to RS - will attenuate input signal.
● Larger RE permits larger RB, but results in lower gain.
● Gain = -RC/RE for RE >> re.
● Split RE with bypassing increa ....etc

[:=Read Full Message Here=:]

Definition

In order to conserve natural resources and economize energy, weight reduction has been the main focus of automobile manufacturers in the present scenario. Weight reduction can be achieved primarily by the introduction of better material, design optimization and better manufacturing processes. The suspension leaf spring is one of the potential items for weight reduction in automobiles as it accounts for 10% - 20% of the unsprung weight. This achieves the vehicle with more fuel efficiency and improved riding qualities.

The intro ....etc

[:=Read Full Message Here=:]

Submitted By
Vinit Tarey


ABSTRACT
Many system-on-chip (SoC) integrated circuits contain embedded cores with different scan frequencies. To better meet the test requirements for such heterogeneous SoCs, leading tester companies have recently introduced port-scalable testers, and Many IP core design software like Xilinx, Leonardo Spectrum, and Modelsim etc which can used to design ip core like DMA ,Interrupt Controller etc .These Ip core can be Power aware an Implement on soc by choosing different design tech ....etc

[:=Read Full Message Here=:]

blockdiagram of electronic voting machine..
and implementation

block diagram and implementation of electronic voting machine ....etc

[:=Read Full Message Here=:]

PRESENTED BY:
S.VENKATESH


LEAN IMPLEMENTION IN FINISHING LINE
In the global competitive environment, that there is a need to improve the delivery of products and services to compete in the market and to satisfy the huge expectations of customer. Though many efforts have been devoted in the past to improve the delivery products and services to maintain the higher level of customer satisfaction through many system improvement techniques and methodologies which were introduced by various Quality veterans all over ....etc

[:=Read Full Message Here=:]

This article is presented by:
Sapana Mehta


Design Patterns


A pattern is a proven solution to a problem in a context.
Christopher Alexander says each pattern is a three-part rule which expresses a relation between a certain context, a problem, and a solution.
Design patterns represent a solutions to problems that arise when developing software within a particular context.
i.e Patterns = problems.solution pairs in a context

Background

Started in 1987 by Ward Cunningham and Ken Beck who were workin ....etc

[:=Read Full Message Here=:]

Definition

Success is all about being in the right place at the right time ?.. and the axiom is a guiding principle for designers of motorsport circuits. To avoid problems you need know where and when things are likely to go wrong before cars turn a wheel -and anticipating accidents is a science.

Take barriers, for example .there is little point erecting them in the wrong place -but predicting the right place is a black art. The FIA has developed bespoke software, the Circuit and Safety Analysis System (CSAS), to predict problemareas on F ....etc

[:=Read Full Message Here=:]

Formal methods have been advocated as one of those techniques that can produce highquality software and hardware systems that has been demonstrated to come in ontime, within budget, and satisfy procurer requirements. They are, however, perceived to be difficult to use and unsuitable for presentation to nonspecialists. In addition, they have been criticized for paying too little attention to the system development process.

Traditional structured (bubblesandarrows) methods, however, do excel at supporting the development process, but do not ....etc

[:=Read Full Message Here=:]